Freud Woodworking

is a small, family-owned business that has been in operation since 2004. We are a general woodworking shop, specializing in custom woodworking, furniture, and cabinetry. We take pride in our work, and we are dedicated to providing our clients with quality products and services.

Our shop is equipped with a wide variety of tools and equipment, including a CNC router, a wide-belt sander, and a panel saw, which allows us to fabricate a wide range of products, from small pieces of furniture to large cabinets and fixtures. We also have a team of experienced and skilled craftsmen who can take your project from start to finish.

If you are looking for a quality woodworking shop that can provide you with a wide range of products and services, Freud Woodworking is the shop for you. Contact us today to discuss your project.

What Is A Dado Cut In Woodworking

?

In carpentry, a dado (US) or dadoe (UK) is a slot or trench cut into the face or edge of a piece of lumber, plywood or other sheet material. A dado is cut with a dado blade, a type of saw blade specifically designed for this purpose. dadoes are often used to create a joint that is stronger than a simple butt joint. They are also used to conceal the end grain of a board.

When creating a dado, the width of the cut is usually equal to the thickness of the material that will be inserted into the dado, minus the width of the dado blade. For example, if you are using a dado blade that is 3/8 inch wide, you would want to make a dado that is only 7/8 inch wide. The height of the dado is usually equal to the thickness of the material that will be inserted into the dado, minus the height of the dado blade.

There are several different types of dadoes that can be cut, depending on the application. The most common type of dado is a through dado, which is cut all the way through the piece of lumber. A stopped dado is one that is cut only partially through the piece of lumber. A blind dado is one that is cut only partially into the piece of lumber and does not go all the way through.

When creating a dado, it is important to make sure that the blade is set to the correct height. If the blade is set too high, the dado will be too wide. If the blade is set too low, the dado will be too narrow. It is also important to make sure that the fence is set to the correct distance from the blade. If the fence is set too far from the blade, the dado will be too wide. If the fence is set too close to the blade, the dado will be too narrow.

There are a few different ways to make a dado. The most common way is to use a dado blade in a table saw. However, a dado can also be made with a chisel or a router.

READ
Craigslist Kansas City Woodworking Tools

Woodworking Logs Into Planks

In carpentry, a log is a piece of squared or round wood, a trunk of a tree, from which planks are cut. In the United States and Canada, a log is also called a “stick”. A log is a natural product and depending on the moisture content, the weight and the size of the log, the time needed to air dry it may vary. Green, freshly cut wood may have a moisture content of 60-70%. The air-drying process reduces the moisture content to 18-22%.

The process of converting logs in to lumber is called sawing. The goal of sawing is to produce lumber with a thickness of 1.5 inches (3.8 cm) or less. There are three main types of sawing:

1. Plain sawing is the most common type of sawing and it is used to produce lumber with a rectangular cross-section.

2. Quarter sawing is used to produce lumber with a more decorative cross-section. In quarter sawing, the log is first cut in to quarters. Each quarter is then cut in to boards that are the same width as the finished lumber is desired.

3. Rift sawing is used to produce lumber with a more uniform grain pattern. Rift sawing is a variation of plain sawing. In rift sawing, the log is first cut in to two halves. The two halves are then cut in to boards that are the same width as the finished lumber is desired.

What Size Nailer For Woodworking

?

There is no one size nailer for woodworking. The right size nailer for the job depends on the type of wood, the thickness of the wood, and the type of nails you are using.

There are three main types of nails: finishing nails, brad nails, and clout nails. Finishing nails are the smallest, with a diameter of about 1.5 mm. They are used for delicate work where a small nail is needed. Brad nails have a diameter of about 2.5 mm, and are used for light-duty work. Clout nails have a diameter of about 3.5 mm, and are used for heavy-duty work.

The thickness of the wood also affects the size of the nailer you need. Finishing nails are usually used for wood that is less than 1/2 inch thick. Brad nails are usually used for wood that is less than 1 inch thick. Clout nails are usually used for wood that is more than 1 inch thick.



The type of wood you are using also affects the size of the nailer you need. Hardwoods, such as oak, are harder to nail than softwoods, such as pine. For hardwoods, you will need a nailer that can drive nails through the wood with more force. For softwoods, you will need a nailer that can drive nails into the wood more easily.

There are several different types of nailers available, each with its own strengths and weaknesses. The most common types of nailers are:

-finishing nailers
-brad nailers
-clout nailers
-stapler/nailers

READ
Why Did Matt Kenney Leave Fine Woodworking

Finishing nailers are the smallest and most delicate of the three types of nailers. They are used for nailing delicate trim work and molding. They can only drive nails that have a diameter of 1.5 mm or less.

Brad nailers are the most common type of nailer. They are used for nailing light-duty work, such as trim work, paneling, and furniture. They can drive nails that have a diameter of 2.5 mm or less.

Clout nailers are the largest and most powerful of the three types of nailers. They are used for nailing heavy-duty work, such as framing and decking. They can drive nails that have a diameter of 3.5 mm or less.

Stapler/nailers are a type of nailer that can drive both nails and staples. They are used for nailing and stapling light-duty work, such as trim work, paneling, and furniture. They can drive nails and staples that have a diameter of 2.5 mm or less.

Used Woodworking Machinery Auctions

If you are in the market for used woodworking machinery, you may want to consider looking into auctions as a source. Auctions can be a great way to find quality used machinery at a fraction of the cost of buying new.

When looking for used woodworking machinery at auction, there are a few things to keep in mind. First, it is important to know what you are looking for. This will help you focus your search and make sure you are not wasting time looking at machinery that will not work for your needs.

Once you know what you are looking for, it is important to do your research. Find out what the average price is for the type of machinery you are interested in. This will give you a good idea of what you should be prepared to pay at auction.

Also, be sure to check the condition of the machinery. This can be done by looking at pictures or videos of the machinery in operation, or by reading the auction listing carefully. If you are not familiar with the machinery, be sure to ask the seller questions to make sure you know what you are buying.

Finally, be sure to factor in the cost of shipping the machinery. This can be expensive, so it is important to budget for it.

When looking for used woodworking machinery, auctions can be a great way to find quality machinery at a fraction of the cost of buying new. By doing your research and knowing what to look for, you can find the machinery you need and get it for a great price.



Send this to a friend